Resmed HumidAire 3i Bedienungsanleitung PDF herunterladen (Seite 3)

English

Please ensure that you read the entire guide before using the Humidier.

Indications for Use

The Humidier is intended for humidication of the air delivered from a

ResMed compatible CPAP therapy device. This device is for use only as

recommended by a physician.

Contraindications

This device is contraindicated for use with patients whose upper

(supraglottic) airway has been bypassed. Please also refer to the relevant

system manual for the contraindications associated with Positive Airway

Pressure (PAP) therapy.

Humidier parts

Refer to Illustration A on page 1.

Your heated Humidier is made up of two main parts:

(1) docking station and (2) water chamber. Your docking station has the

following items (3) air outlet; (4) cover; (5) cover seal; (6) control dial; (7)

connector seal; (8) heater plate; (9)lLatch.

Setting up your Humidier for use

Refer to illustrations B & C on page 1.

Remove the connector plug from your ow generator (a) and attach it to

the back of the docking station (b).

Align your Humidier with your ow generator and push together until

they click into place.

Connect the power cord to the socket on the rear of your ow

generator.

Plug the other end into a power outlet. Place the combined unit on

a rm, level surface near your bed at a level lower than your sleeping

position. Ensure the surface is not sensitive to heat and/or moisture, or

use a protective mat.

Connect one end of the air tubing rmly onto the air outlet.

Connect the assembled mask system to the free end of the air tubing.4.

WARNING

Make sure your ow generator is disconnected from the power •

outlet before connecting to docking station.

The Humidier docking station should only be connected or •

disconnected when the water chamber is empty.

Do not transport the ow generator with the Humidier attached.•

Filling the water chamber

Refer to illustration D on page 1.

1. Open the cover.

Remove the water chamber.2.

Fill with fresh, clean water to the maximum water level mark.3.

Return the water chamber to the docking station.4.

Close the cover ensuring that it clicks into place.5.

WARNING

Do not overll the water chamber as water may enter the ow

generator and air tubing.

CAUTION

Do not use any additives (eg, scented oils or perfumes). They may

reduce the humidication output of the Humidier and/or cause

deterioration of the water chamber materials.

Warming your Humidier

(Not available on all ResMed PAP devices)

Select warmup by pressing

on the control panel.

The WARMING screen will appear to indicate that the Warm-Up feature 1.

is activated.

While your Humidier is in Warm-Up mode you can:

Start treatment at any time by pressing •

Access menus by pressing •

Stop the Warm-Up feature at any time by pressing • .

Starting your Treatment

Turn the humidity control dial to three (1. ). You can adjust the

control dial up or down at any time to nd the setting that is most

comfortable for you. The

setting switches heated humidication

o and delivers minimum humidication while a setting of six ( )

delivers maximum humidication.

Fit your mask as described in your mask user instructions.

Press 3. on the control panel to begin therapy.

Note: The indicator light will brighten to indicate when the device is

heating and dim when it has reached its set temperature.

Lie down and arrange the tubing so that it moves freely when you

turn in your sleep

WARNING

Do not leave an excessive length of air tubing around the top of your

bed. It could twist around your head or neck while you are sleeping.

Stopping your Treatment

To stop your treatment, remove your mask and press .

Detaching your Humidier

Refer to illustration E page 1.

Unplug the power cord from the power outlet.

WARNING

Take care when handling your Humidier. The water and water

chamber base may be hot. Allow 10 minutes for the heater plate and

any excess water to cool.

Remove the water chamber from the docking station.

Press the large silver button3. located midway underneath the docking

station and pull the Humidier and ow generator apart.

Cleaning and Maintenance

You should regularly carry out cleaning and maintenance of the water

chamber, cover and cover seal as described in this section.

WARNING

Beware of electric shock. Do not immerse your ow generator,

docking station or power cord in water. Always unplug the device

before cleaning and be sure that it is dry before plugging it back in.

Cleaning the Water Chamber

Refer to illustration F on page 2.

Daily

Wash the assembled water chamber, tub plate and tub plate seal in

warm water, using a mild detergent. Rinse thoroughly in clean water and

allow them to dry away from direct sunlight.

Disassembling the Cleanable Water Chamber

Refer to illustration G on page 2.

Discard any excess water from the water chamber.

Turn the water chamber upside down. Using the side tabs, disengage 2.

the latch by pushing the latch up and away.

Remove the tub plate.

Remove the tub plate seal.4.

Weekly

The disassembled water chamber, tub plate and tub plate seal may be

washed in a dishwasher on the delicate or glassware cycle (top shelf

only).

Inspect the water chamber for wear and deterioration. Replace the

water chamber if any component has cracked, become cloudy or pitted.

Replace immediately if there is any leaking from the water chamber.

White powder or deposits in the water chamber can be cleaned using a

solution of one part vinegar to 10 parts water as follows:

Refer to illustration H on page 2.

1. Fill the cleaning plug to the rim with vinegar and pour into empty

water chamber.

2. Add clean water to the water chamber until the solution reaches the

maximum water level mark.

1 2 3 4 5 6 7 8 ... 23 24

Kommentare zu diesen Handbüchern

Keine Kommentare

Resmed HumidAire 3i Bedienungsanleitung Seite 3

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Luftbefeuchter Resmed HumidAire 3i